Microsonic lcs-25/DD/QP Manual de usuario descargar pdf

Sensor adjustment with Teach-in procedure

Adjust detect point D1

Place object at position 

Adjust window mode D1

Place object at position 

Adjust two-way reflectiv

barrier D1

Place reflector at position 

Set NOC/NCC D1

Adjust detect point D2

Place object at position 

Adjust window mode D2

Place object at position 

Adjust two-way reflectiv

barrier D2

Place reflector at position 

Set NOC/NCC D2

Connect Com to +U

until both

LEDs flash simultaneously

(ca. 3 s)

Both LEDs:

flash

mutually

Connect Com to +U

for about 1 s

Connect Com to +U

until both

LEDs flash simultaneously

(ca. 3 s)

Both LEDs:

Place object at position 

flash

mutually

Beide LEDs:

Connect Com to +U

for about 1 s

blinken

wechselseitig

Connect Com to +U

until both

LEDs flash simultaneously

(ca. 3 s)

Both LEDs:

flash

mutually

Connect Com to +U

until both

LEDs flash mutually

(ca. 13 s)

LED D1:

LED D2:

Connect Com to +U

for about 10 s

To change output characteristic

connect Com to +U

for about 1 s

Wait for 10 s

on: NOC

off: NCC

flashes

Connect Com to -U

until both

LEDs flash simultaneously

(ca. 3 s)

Both LEDs:

flash

mutually

Connect Com to -U

for about 1 s

Connect Com to -U

until both

LEDs flash simultaneously

(ca. 3 s)

Both LEDs:

Place object at position 

flash

mutually

Beide LEDs:

Connect Com to -U

for about 1 s

blinken

wechselseitig

Connect Com to -U

until both

LEDs flash simultaneously

(ca. 3 s)

Both LEDs:

flash

mutually

Connect Com to -U

until both

LEDs flash mutually

(ca. 13 s)

LED D2:

LED D1:

Connect Com to -U

for about 10 s

To change output characteristic

connect Com to -U

for about 1 s

Wait for 10 s

on: NOC

off: NCC

flashes

Normal mode operation

85 %

Instruction manual

lcs-Ultrasonic Sensors with

two switched outputs

lcs-25/DD/QP

lcs-35/DD/QP

lcs-130/DD/QP

Product description

 The lcs-sensor with two switched outputs

measures the distance to an object within

the detection zone contactless. Depending

Ultrasonic Sensors

on the adjusted detect distance the switched

outputs are set.

 The output functions are changeable

from NOC to NCC.

 Light emitting diodes (three-colour

LEDs) indicate the switching status.

 The sensors can be trained using Teach-

in processes.

 Using the LinkControl adapter (optional

accessory) all sensor parameter settings

may be made by a Windows-Software.

Important instructions for assembly and

application

All employee and plant safety-relevant

measures must be taken prior to assembly,

start-up, or maintenance work (see operation

manual for the entire plant and the operator

instruction of the plant).

The sensors are not considered as safety

equipment and may not be used to ensure

human or machine safety!

The lcs-sensors indicate a blind zone, in

which the distance cannot be measured. The

operating range indicates the distance of the

sensor that can be applied with normal re-

flectors with sufficient function reserve.

When using good reflectors, such as a calm

water surface, the sensor can also be used up

to its maximum range. Objects that strongly

absorb (e.g. plastic foam) or diffusely reflect

sound (e.g. pebble stones) can also reduce

the defined operating range.

Assembly instructions

 Assemble the sensor at the installation

location.

 Plug in the connector cable to the M 12

connector.

Fig. 1: Pin assignment with view onto sensor

plug and colour coding of the

microsonic connection cable

Assembly distances

The assembly distances shown in Fig.2 for

two or more sensors should not be fallen

below in order to avoid mutual interference.

Fig. 2: Assembly distances

colour

-U

brown

blue

black

white

Com. grey

>10 cm

>30 cm

>1,0 m

>1,7 m

>60 cm

>5,4 m

Start-up

lcs sensors are delivered factory made with

the following settings:

 Switched outputs on NOC

 Detecting distances at operating range

and half operating range

 Measurement range set to maximum

range

Set the parameters of the sensor using the

Teach-in procedure.

Operation

lcs- sensors work maintenance free. Small

amounts of dirt on the surface do not influ-

ence function. Thick layers of dirt and caked-

on dirt affect sensor function and therefore

must be removed.

Note

 mic+sensors have internal temperature

compensation. Because the sensors heat

up on their own, the temperature com-

pensation reaches its optimum working

point after approx. 30 minutes of opera-

tion.

 During normal mode operation, a yel-

low LED signals that the corresponding

switched output has connected.

 During Teach-in mode, the hysteresis

loops are set back to factory settings.

 If no signal is transmitted to the Com

input for 20 s during parameter setting

mode the made changes are stored and

the sensor returns to normal mode ope-

ration.

 You can reset the factory settings at any

time, see »Lock Teach-in & factory set-

ting«

 lcs-sensors optional can be programmed

using the LinkControl adapter LCA-2,

see «Optional setting of parameters

using the LinkControl Adapter LCA-2».

*B7300*

MV-DO-074380-234282

Set switched output D1

Set switched output D2

2004/108/EC

Lock Teach-in & factory setting

Activate/deactivate

Teach-in

Reset to factory

setting

Turn supply voltage OFF

While Com is connected

to -U

turn on

power suply

Turn supply voltage OFF

While Com is connected

to -U

turn on

power suply

Keep Com connected to

-U

until both LEDs flash

simultaneously

(ca. 3 s)

LED D1:

LED D2:

on: Teach-in

activated

off: Teach-in

deactivated

flashes

To activate or

deactivate Teach-in

connect Com to -U

for

about 1 s

Wait for 10 s

Keep Com connected to

-U

until both LEDs

stop flashing

(ca. 13 s)

Normal mode operation

1 2 3

Instruction manual 1
Technical data 2

Indice de contenidos

Pagina 1 - Instruction manual

Sensor adjustment with Teach-in procedureAdjust detect point D1Place object at position  Adjust window mode D1Place object at position  Adjust two-w

Pagina 2 - Technical data

Technical dataBlind zoneOperating rangeMaximum rangeAngle of beam spread0 to 30 mm250 mm0 to 65 mm350 mm350 mmSee detection zone600 mmSee detection zo

Pagina 3

microsonic GmbH • Hauert 16 • D-44227 Dortmund • Tel: +49 2 31 / 97 51 51-0 • Fax: +49 2 31 / 97 51 51-51 • E-Mail: [email protected] • www.microsoni

Modelos relacionados lcs-35/DD/QP | lcs-130/DD/QP |

Comentarios a estos manuales

Sin comentarios

Microsonic lcs-25/DD/QP Manual de usuario

Busca en linea o descarga Manual de usuario para Sensores Microsonic lcs-25/DD/QP. Microsonic lcs-25/DD/QP User Manual Manual de usuario

Indice de contenidos

Modelos relacionados lcs-35/DD/QP | lcs-130/DD/QP |

Comentarios a estos manuales

Relacionado con productos y manuales para Sensores Microsonic lcs-25/DD/QP